Home xin Who has the packing specification of wooden door? It is more detailed and can be directly used as the acceptance standard of workers in other factories.

Who has the packing specification of wooden door? It is more detailed and can be directly used as the acceptance standard of workers in other factories.

by admin
0 comment

acceptance criteria for wooden door products: 1. The whole door surface shall be free of scratches, bumps and other injuries. 2. The color is consistent with the customer’s requirements without obvious color difference. Bright color and clear wood grain. 3. The color of the whole batch of doors is consistent without obvious color difference. Meet the requirements of customer gloss. 4. The paint surface shall be free of sagging, shrinkage, edge expansion and wrinkle, and the line corners shall be basically consistent with the surface, without paint accumulation, abrasion and other defects. 5. The size of the whole door is consistent with the size of the opening. 6. The color on both sides of the wooden door is consistent without obvious difference. 7. The coating surface shall be free of obvious processing traces and coloring defects. 8. Produce according to the drawings and processing technology, with real materials. 9. The wooden door shall be flat, square and free from warpage. Meet the tolerance requirements (national standard). 10. There shall be no gap between the movable parts and the product. 11. The hinge shall be installed without skew, and the hole shall be punched according to the mold, and the position of the lock hole shall be accurate. 12. The alignment is uniform; The depth of the notch is the same without wave curvature. 13. The installation gap of door panel shall be uniform and meet the requirements, and the door pocket shall be installed squarely without skew. 14. The door leaf can be opened flexibly without abnormal noise. 15. The door pocket and the wall shall be sealed with sealant on both sides and cut flat after drying. 16. Fixing screws shall be used between the door pocket and the wall, with no less than 3 screws per meter. 17. The sleeve line on the same side shall be on one plane, and the gap shall be filled with sealant. 18. The threading interface must be flat, and the allowable tolerance of threading curvature is 1mm. 19. The door leaf shall be tightly combined with the sealing strip without swinging. Acceptance criteria for wooden door installation: I. door pocket installation: 1. The connection of door pocket assembly shall be tight, flat and free of black joints; Fixed accessories shall be locked; The diagonal line of door pocket shall be accurate. The allowable tolerance within 2m is ≤ 1mm, and the allowable tolerance above 2m is ≤ 1.5mm; 2. After the door pocket is installed, it shall be three-dimensional horizontal and vertical, the allowable tolerance of perpendicularity is + 2mm, and the allowable tolerance of horizontal flatness is + 1mm; The combination between door pocket and wall shall have fixing screws (no less than 3 per linear meter); If the door pocket width is more than 200mm, fixed iron sheets shall be added; The gap between the door pocket and the wall shall be sealed with Styrofoam on both sides. The styrofoam shall be coated evenly and cut flat after drying. 7 II. Wire installation: 1. The wire installation shall be uniform, and the interface between the gum and the door pocket and the wall fixed sleeve shall be flat, tight and seamless. After installation, the same side sleeve line shall be in the same plane; Because the wall is not flat, it is necessary to ensure that the socket line interface is flat. The allowable tolerance for the camber of the jacketed line is 1mm. The gap between the sleeve line and the wall shall be filled with sealant. 3、 Door leaf installation: 1. After installation, the door leaf shall be flat and vertical, and the door leaf shall be flush with the exposed surface of the door pocket; There is no abnormal sound when the door leaf is opened, and the switch is flexible; 2. For the gap between the door pocket and the door leaf, the lower seam is 6mm, and the other three sides are 2mm; The allowable tolerance of all gaps is + 0.5mm; 3. After the door leaf is closed tightly, it is closely combined with the sealing strip without swinging. 4、 Hardware: 1. The door hinge shall be vertical and flat; The flat hinge shall be slotted corresponding to the door leaf and door pocket. The notch shall be standardized, the size shall be the same as the hinge, and the allowable tolerance on three sides shall be + 0.5. After assembly, it shall be flat and seamless, and the hinge shall be opened flexibly. The Trident hinge shall be installed according to the mold, and the bolt shall be inserted in place. The hinge fixing screws shall be installed completely, straight and hidden in the hinge plane. 2. The slotting of the door lock shall be accurate and standardized, and the size shall be consistent with the lock body and lock plate; The door lock shall be installed firmly and unlocked freely without abnormal sound; The accessories shall be installed completely, and the fixing screws shall be installed completely and straightly. 3. The door opener, door closer and handle shall be installed at the designated position and firmly installed. The fixing screws shall be installed completely and straight, and the effect of accessories after assembly is good. 5、 Appearance: 1. The joint gap between the sleeve, door line and the ground shall be less than 3mm, and the gap 8402 shall be sealed with waterproof sealant. After the whole door is installed, it shall be flat and uniform, open freely and flexibly, and the overall effect is good without scratches wa… The rest is>>

You may also like

Leave a Comment